How To Install A One Piece Fiberglass Shower Stall

Download Article

Download Commodity

Many homeowners are opting for the improver of a shower stall as a functional alternative to a total bathtub. Plumbing and carpentry skills are required to successfully install a shower stall. Ever follow manufacturer'south instructions and seek consultation from professionals if necessary. If you lot're renovating a bath, or planning a new addition to your home and you're prepare to install a shower stall, there are a few steps you must follow.

1. 1

   Determine the ideal location. Whether you're installing a shower stall to salve space in a new bathroom, or to replace a tub, the stall should be located in proximity to hot and cold water pipes, an it must exist able to have access to your drainage pipes.

2. 2

   Decide on the type of stall. A quick search on the Internet or a walk through the plumbing aisles of a home improvement store will reveal the many different kinds of shower stall on the marketplace. A wide variety of options are available, including those with features such equally a bench for sitting within the stall, shapes ranging from rectangles to semi-circles, and sizes to fit any need. That said, at that place are also a few specific varieties, and the differences betwixt them can bear on the installation process.^[1]

   • Unmarried-piece prefabricated showers are complete units, usually fabricated of fiberglass or acrylic. They tend to exist more than expensive than other shower stall sets, and some also claim that they can be more difficult to install. Every bit you could probably gauge, the consummate unit can be a chip bulky, and for that reason difficult to carry through doorways or up stairs. On the plus side, they tend to be solidly constructed and easier to make clean.
   • Interlocking multi-slice units will commonly come up in a set of iv to vi big pieces, including the shower pan (the base expanse where you would stand up in the shower and that connects to the drain), wall coverings (for the side(s) where the unit of measurement will be mounted along the bath wall), side sections (that will not be placed along the bathroom wall), and a door. Quite a few of these kits are considered easy to get together, and they generally price much less than unmarried-piece units.

   Advertizement

3. 3

   Purchase materials. At that place is an extensive list of materials that will take to be acquired in order to complete this project. Here is a partial listing.

   • Plumbing pipes and fittings. Non just do you need to brand sure that you accept plenty pipage, you must too be certain to obtain the advisable parts that will allow y'all to connect the new pipes to existing ones.
   • Shower unit of measurement/kit.
   • Waterproof caulk/sealant. It is probably best to obtain a silicone-based sealant or caulk, a diversity known for their resistance to water.
   • Tools, such as wrenches and screwdrivers.

4. iv

   Read the instructions that come with your shower unit or kit. While some provide very trivial detail, most will include instructions that explain how the shower will fit into place. Even those that don't directly explain the process you lot must follow will certainly propose what prerequisites are required for installation.

   Advertisement

1. ane

   Clear and prepare the intended shower site. It may exist preferable to remove bathroom tiles or other floor coverings and install the shower directly on the base of the flooring itself. You must also identify the appropriate location for the drain hole--mensurate the shower pan to determine the location--and cut a pigsty through the floor.

   • If your plumbing is coming through a wall and not, say, a basement area in which the pipes are exposed, you must tear out the portions of the wall. Obviously, this must be one of your first steps.

2. ii

   Build a frame to back up the stall (if applicable). Some shower kits will require that you build a construction to support the shower pan or fifty-fifty brace a whole prefabricated unit. Oftentimes the unit will accept to be screwed into place, and so y'all must build the required structures that volition allow you to do so.^[2]

   • For some units, at least some of the frame edifice will take to exist completed afterward the shower stall has been put into identify. Read the instructions advisedly.
   • Some multi-piece shower kits come with a kind of frame that volition be used to hold upward the sides. Once again, go through the instructions that came with your kit before you install in order to determine how your shower stall will fit into your bath.

3. iii

   Install the shower pan/prefabricated unit. Slide the pan or unit in identify and attach it using screws. ^[iii]

4. 4

   Install the plumbing (if you have not already done and then). For some installations, this may have been the beginning job that was required. For others, it should be near the finish. Follow these steps:

   • Turn off the main water supply.
   • Utilizing traditional plumbing methods, run hot and cold pipes to correspond with the holes for faucet handles in the shower stall. Attach the correctly threaded extension pipage for the shower caput, using thread seal tape and a pipe wrench. Install the faucet handles and the shower head. Turn the main water supply on and check for leaks.
   • Connect the drainage lines. Secure the drain pipe with the drain kit (that either came with the unit or was purchased separately). The bleed should be sealed with plumber'south putty and tightened into identify to foreclose leakage. (For more on plumbing a bathroom, see guides hither and here.)

5. v

   Install the sides of the shower stall (if applicable). Shower kits with multiple pieces will require this footstep, but it is one that really tin be delayed until the project is about consummate. If you don't want to work on plumbing inside of a tiny shower stall, chose to exit this pace for the terminate.

   • For some kits, the side mounted to the wall will have to be screwed into place, while others simply recommend that your utilise heavy duty caulk. Keep this in heed when purchasing your sealants, as some can also be used equally adhesives.

6. 6

   Finish the projection. Encompass any exposed framing with water-resistant drywall and seal all seams that will be exposed to water with the silicone-based caulk. Texture and paint as desired. Attach the shower door or curtain.

   Advertisement

Add New Question

• Question

  How long does it take to install a shower stall?

  

  Plan on at least a full twenty-four hours, sometimes more if y'all're inexperienced.

• Question

  Does a i-piece shower stall need a shower pan?

  

  Not if it has ane of its own. If information technology doesn't, then it'southward just a one-piece "environs" or "enclosure," and you will absolutely need a shower pan and the rest of the shower floor.

• Question

  What type of shower is the easiest to go on clean?

  

  Plastic. No grout lines, no caulk, and no leaks. Just don't put anything metallic on the shelves that rusts - sometimes only sanding can remove those marks.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

• Variable speed drill and screws
• Record measure
• Level
• Framing lumber (if applicable)
• Thread seal record
• Pipe wrench
• H2o resistant drywall
• Silicone

About This Article

Article Summary X

To install a shower stall, beginning past clearing the area and drilling a hole in the floor for the drain. Then, build a frame to support your shower tray according to the instructions of your shower kit. Subsequently the frame is set up, slide the tray into position and screw it in place. Next, turn off the water supply before installing hot and cold water pipes. In one case the plumbing is done, cover any exposed parts of the frame with h2o-resistant drywall and seal seams or cracks with silicon-based caulk. Finally, install the sides of the stall if required. For tips on how to decide on a location for your shower and which blazon of stall to cull, read on!

Did this summary help y'all?

Cheers to all authors for creating a page that has been read 133,637 times.

Did this article help y'all?

Source: https://www.wikihow.com/Install-a-Shower-Stall

Posted by: rodriguezhustry.blogspot.com

Share this post